Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Canoga Park Homeowners
If your chimney cap is rusted through, dented, or missing entirely, rain and animals get a free path into your flue. If the crown on top of the chimney is cracked, water works its way into the masonry every time it rains, and that damage gets more expensive the longer it sits. Our technicians have up to 15 years of experience spotting both problems, and we carry cap and crown options from Gelco, Famco, and Copperfield so the fix fits your flue instead of a one-size guess. We can often handle same-day work in Canoga Park when you call early. Reach us at (844) 443-4582. We answer 24/7.
What Our Chimney Cap & Crown Service Includes
Most homeowners don’t think about the top of the chimney until something goes wrong. Here’s what each part of the job covers and when it matters.
Cap Installation
A chimney cap is the metal lid that sits over the flue opening, and it’s the cheapest protection you can put on a chimney. It keeps rain out of the flue, stops birds and squirrels from nesting inside, and catches sparks before they land on the roof. We size the cap to your actual flue dimensions rather than guessing, then secure it so it holds up against wind on an exposed roofline.

Cap Replacement
Replacement makes sense when an existing cap is rusted through, bent out of shape, or too small for the flue. A damaged cap that’s still in place can look fine from the ground while letting water in around the edges. We pull the old cap, check the flue tile and the top of the chase for damage the failing cap may have allowed, and set a new one that seals correctly.

Crown Repair
The crown is the concrete or masonry surface that slopes across the top of the chimney and sheds water away from the flue. When it cracks, water gets into the brick and mortar below and starts breaking the chimney down from the inside. We repair cracked crowns with proper slope and bonding so water runs off the way it’s supposed to instead of pooling.

Crown Coating
Crown coating is a protective layer applied over a crown that’s still structurally sound but showing surface wear. It seals small cracks and hairline fissures before they widen into real damage, and it’s a lower-cost option than a full rebuild. We only recommend coating when the crown underneath is solid enough to justify it. If the crown is crumbling, coating won’t fix that and we’ll tell you so.
Multi-Flue Cap
A single chimney can serve more than one flue, and a multi-flue cap covers all of them under one housing. This keeps a clean look on the roofline and protects each flue opening at once. We measure every flue in the stack, build the cap to match, and make sure each opening still drafts the way it should.
Custom Cap
Older homes, unusual flue sizes, and chimneys on steep or complex rooflines sometimes need a custom cap. A stock cap that doesn’t fit properly leaves gaps, rattles in the wind, or blocks airflow. We take measurements on site and have a cap made to the exact dimensions of your chimney so it sits right and lasts.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with Gelco caps and crowns, and we know where those products hold up and where they wear out over time. Gelco makes sturdy multi-flue and single-flue caps, and fitting them correctly comes down to accurate measurements and a secure mounting method. When a Gelco cap on your chimney is damaged, we can match or replace it without pushing you toward a completely different product line.
Famco and Copperfield caps are both part of what we install, and each fits different chimney styles and flue sizes. Famco caps handle standard residential flues well, while Copperfield offers options for homeowners who want a specific look on the roofline. We also source materials through Olympia Chimney Supply, a nationally recognized chimney products distributor, so the parts we bring are professional-specification rather than whatever’s on a hardware store shelf. Whether you have a Gelco, Famco, or Copperfield cap, or any other make, we can help.
Signs You Need Chimney Cap & Crown Right Now
- Rust or holes in the cap. Rust that’s eaten through the metal means the cap is no longer keeping water out of the flue. Once it’s failing, rain goes straight down the chimney and into the firebox area.
- Water stains on the ceiling or chimney chase. Staining near the chimney usually points to a cracked crown or a failed cap letting water in. Finding it early keeps a small repair from turning into masonry work.
- Cracks or crumbling in the crown. Visible cracks, flaking concrete, or pieces breaking off the top of the chimney all signal that the crown is no longer shedding water. This is the single most common cause of long-term chimney damage we see.
- Birds, squirrels, or nesting debris in the flue. An open or missing cap gives animals an easy way in, and nests block the flue and create a fire risk. A properly fitted cap closes that opening for good.
- Draft problems or smoke coming back into the room. A cap that’s the wrong size or blocked with debris can hurt how the chimney draws. A quick inspection tells you whether the cap is the cause or something else is going on.
Our Chimney Cap & Crown Process – Step by Step
- 1
We inspect before we quote. We look at the cap, the crown, the flue tile, and the top of the chase from the roof, and we check the firebox side too. You get a clear picture of what’s actually wrong before anyone recommends a repair.
- 2
We explain what we found and what it will take. You’ll hear what’s damaged, what’s still serviceable, and what can safely wait. If the crown only needs coating and not a rebuild, we say so.
- 3
We measure for the right fit. Cap sizing comes down to the exact flue dimensions and the shape of the chimney top. We take measurements on site so the cap or crown material is made to fit, not trimmed to sort of fit.
- 4
We install with proper sealing and slope. The crown gets the right slope so water runs off rather than pooling, and the cap gets secured so wind can’t shift it. Small details here decide how long the repair lasts.
- 5
We do a final check before we leave. We confirm the cap sits level, the crown drains, and the flue still draws correctly. Then we walk you through what we did and what to watch for going forward.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Canoga Park?
A typical chimney cap installation in Canoga Park runs $150 – $450 depending on flue size and whether it’s a single-flue or multi-flue setup. A custom cap for an unusual chimney tops that range. Crown repair usually runs $300 – $700, and crown coating sits lower, around $200 – $450, when the crown is still sound. A full crown rebuild on a badly deteriorated chimney will run higher and depends on the size and condition of the top of the chimney.
What pushes the price up: the number of flues, whether the crown needs rebuilding versus repair, how accessible the roof is, and whether the inspection turns up other damage the failing cap allowed. What keeps it reasonable: catching a cracked crown before water gets into the masonry underneath, and choosing a cap sized correctly the first time.
To avoid overpaying, ask for a written estimate that lists the cap or crown work separately from any other repairs, and get the inspection findings explained before you agree to anything. Our estimates are free, the price is set per job by the written estimate, and we’ll tell you plainly when a repair can safely wait. Call (844) 443-4582 for an exact quote. We answer 24/7.
Chimney Cap & Crown Near Canoga Park – Our Service Area
We handle chimney cap & crown work across the west San Fernando Valley, including Winnetka, West Hills, Woodland Hills, Chatsworth, Reseda, Porter Ranch, Northridge, Tarzana, Hidden Hills, Bell Canyon, and Santa Susana. These are all a short drive from Canoga Park, and we schedule dispatch Sunday through Friday, 7am to 7pm. If you’re nearby and need a cap or crown looked at, call and we’ll find the next opening. Fast dispatch, 7am-7pm.
Serving Canoga Park, CA – Our Local Coverage Area
We serve Canoga Park and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Canoga Park
A chimney cap is the metal cover over the flue opening that keeps rain, animals, and sparks out. The crown is the concrete or masonry surface at the very top of the chimney that slopes water away from the flue. Together they’re the first line of defense against water damage at the top of the chimney. Call (844) 443-4582 for an exact quote on either one. Estimates are free.
Most cap installations take under an hour once we’re on site, and crown repairs usually take a couple of hours depending on the size of the crown and the material used. Custom caps take longer because they have to be made to measure before they can be installed. We’ll give you a realistic timeline when we quote the job.
Cap installation typically runs $150 – $450, crown repair $300 – $700, and crown coating around $200 – $450 when the crown is still sound enough to coat. Custom caps and full crown rebuilds run higher depending on size and condition. The written estimate sets the final price. Call (844) 443-4582 for an exact quote. Estimates are free.
Yes. We install and service Gelco, Famco, and Copperfield caps, and we source materials through Olympia Chimney Supply. If your existing cap is one of those brands and it’s damaged, we can match it or replace it with the right fit. Whether you have one of those or any other make, we can help.
We can often schedule same-day work in Canoga Park when you call early. We answer 24/7, and fast dispatch runs 7am-7pm, Sunday through Friday. We’re closed Saturday. A call outside dispatch hours is booked into the next opening.
We stand behind our work and our materials, and the warranty details depend on the specific cap or crown product installed. We’ll go over what’s covered when we quote the job so there are no surprises. Ask us about it on the call and we’ll explain exactly what applies to your repair.
Clear access to the fireplace and the area around it inside the house, and make sure we can get to the roof safely. Move vehicles if the driveway blocks ladder access. Beyond that, there’s nothing to do. We bring the tools, the materials, and the measurements. Call (844) 443-4582 to get scheduled. We answer 24/7.
Schedule Your Chimney Cap & Crown Service in Canoga Park Today
A cracked crown or a rusted-out cap gets worse with every rain, and the repair only gets bigger the longer you wait. We inspect first, explain what’s wrong in plain terms, and give you a free written estimate before any work starts. Call (844) 443-4582. We answer 24/7, and fast dispatch runs 7am-7pm, Sunday through Friday. There’s no obligation, and we’ll tell you when a repair can safely wait.
Written by the team at Chimney Sweep Canoga Park.